Arrow Dynamics Nock Adapters Review
Featured Deal
Arrow Dynamics Nock Adapters
New
From $9.99
Get DealArrow Dynamics Nock Adapters
These inserts allow the use of 1/4" Bohning Classic or AAE Z glue-on nocks on Arrow Dynamics carbons. Sold by the dozen only. Weigh 8 grains each. ...read more
MSRP:
$9.99
$9.99
Used Price:
$6.99
$6.99
Sale Price:
$8.99
$8.99
Arrow Dynamics Nock Adapters For Sale
Most Popular Arrow Building
Gold Tip Ballistic Collar System
Reinforce your Gold Tip Traditional Classic and Traditional Classic XT carbon arrows... read more
$25.99
100%
100%
Black Eagle M Micro-Nocks (dozen)
The Black Eagle "M" Micro-Nock is 100% Polycarbonate. Sturdy and dependable, it's... read more
$12.99
Not Rated
Not Rated
Burt Coyote Lumenok® Lighted Push-In Nocks
All new HD Orange! 30% brighter than previous models. Featuring new and... read more
$29.99
Not Rated
Not Rated
NOCKturnal™ Lighted Push-In Nocks
The NOCKturnal™ lighted nock is a breakthrough design that is more affordable... read more
$29.99
90%
90%
Goat Tuff Impact Glue
Bowhunters and target shooters expect a lot from their arrows. That's why... read more
$15.99
80%
80%
Arrow Dynamics Nock Adapters Reviews
If you have AD tapered shafts, you need these.
GF
6 years ago
I gave myself credit for being an "expert" because I've been shooting Arrowdynamics tapered shafts for about 20 years now and I've done about every bad thing that you can do to them. And the only thing that will kill them is hitting something hard when using a press-in nock. The shaft walls are too thin to stand up to the impact forces, one hit on a rock or a re-bar leg will… read more do it. You can glue in a fresh one to double the life of the shaft, but you break that second nock and you're done. These puppies solve that. You can even split a nock without wrecking an arrow. Anyway, if you're gonna spring for the AD shafts, invest a little more in some of these.
Measure your shaft
Willscarlet
8 years ago
You really need to know the I.D. of the shafts you will be using these on. The insert section of these adapters have a diameter of .2456" (FYI) I used these on an Easton 2213 shaft with a Uni-Bushing and a 5/16" glue on nock , and everything worked perfect. May work as a "press-in" if the fit is tight enough, but I would suggest gluing.
Yes, use them
IAd 120
8 years ago
I was concerned with these adapters, because of other reviews stating that they would not fit. Well they are tight, but slightly wet them ,with a hammer tap them easily into the shaft. All this takes less than 5 seconds. These arrows are great, but the standard nock last until the arrow strikes a hard object. These nock adapters make the arrow a complete package.
Dont always fit
Tony
9 years ago
These adapters fit too tight in my Arrow Dynamic arrows. They are very difficult to install. One arrow out of the 6 I installed had to be pounded in with a hammer and one would not install at all. I measured the adapters and they all measured the same. I think the variation is in the ID of the arrow shaft at the nock end. Since they are supposed to be glue-in, I think the OD… read more on the adapter should be smaller.
I would buy this product again end again
J.j riksma
10 years ago
Too bad a 9/32 nok does not fit
Must have for Arrow Dynamic shafts
Toehead
10 years ago
Use these with G-nocks to make a complete arrow. Highly recommend and a step or two above the factory nicks.
Arrow Dynamics Nock Adapters Questions and Answers
Asked by
bowworx
4 years ago
What is the od on the insert before the taper?
These are approximately .213 and are designed for use in the arr
4 years ago
These are approximately .213 and are designed for use in the arrows dynamics that uses the Arrow dynamics standard nock. If you are using the Newer Arrow Dynamics that uses the X nocks these would be to large.
Asked by
Matt
5 years ago
Will these fit in Beman MFX Classic 400 arrow shafts
Unfortunately these will not fit the MFX classic shafts
5 years ago
Unfortunately these will not fit the MFX classic shafts
Asked by
Milan
8 years ago
What size nock is required for these adapters?
These inserts allow the use of 1/4" Bohning Classic or AAE Z glu
8 years ago
These inserts allow the use of 1/4" Bohning Classic or AAE Z glue-on nocks on Arrow Dynamics carbons. Sold by the dozen only.
Asked by
Andrew
9 years ago
Will they fit into a Gold Tip Hunter 500 shaft and work for gluing on 11/32" AAE Z nocks?
No, you need 0149X
9 years ago
No, you need 0149X
Asked by
Kat the horse archer
11 years ago
Will these fit a 17/16 aluminium shaft? if not what have you got that will?
No they will not and we do not have. I do not have any adapters
11 years ago
No they will not and we do not have. I do not have any adapters that will fit that size shaft.
Asked by
ronald the guide
11 years ago
would it fit a 20/20 easton legacy
No, this adapter will not fit in a 2020.
11 years ago
No, this adapter will not fit in a 2020.