The Champion II elevated rest is a simple, time tested design for elite finger shooters. Constructed of anodized aluminum for strength and precision. Uses opposing magnets for a very light, smooth tension and the elevation adjustments on the support arm provide an easily tunable bow rest for perfect arrow flight. ...read more
With a simple yet effective design, this quality Leather String Keeper is... read more
The Lazer Traditional HP Longbow bow strings utilize modern features and function... read more
These 14 strand B-50 bow strings feature an endless loop design makes... read more
This 15 strand three bundle Flemish twist string is constructed from the... read more
This handy string separating tool is just what busy archers need for... read more
Use locktite
While these wire flipper rests do provide an improvement for bare bow recurve shooters in terms of accuracy over shooting right off the rug, you would thik that for the amount of mark-up profit they make over about 25 cents worth of production materials they would come up with an indisputably problem free product? But I've went through a few of these already on different bows… read more with one flaw or another and as far as the lock screws coming loose, that's always a problem with something that sustains constant vibration. Once you get it adjusted, back out the screw without moving anything or mark the place and put a small drop of # 2 Locktite in the hole and that should hold, or at least much longer than they normally do.
Champion II
Surprised to read some of the comments posted. Absolutely no problems with rest and adjusts easily. That's what the hex screws are for. Simple to work with and accurate.
Must adjust every dozen arrows shot
The rest arm creeps out. I thought I needed to just tighten the set screw but never could get it to stay put. I shoot a DAS Dalaa at 55#. Will try something else.
Better than most, still not perfect
Whilst I believe this is the best AAE/Cavalier rest they have ever made, it still pales in comparison to the Shibuya Ultimate rest. This AAE rest is somewhat of a pain to setup(almost need three hands) and requires a good bit of fine tuning to get right. Once set, I haven't had any issues with it. You have to do some bending in order to get the arrow in the center of the plunger… read more and then bend the wire some more to get it to clear the plunger. This may be the case with all wire rests like this but, I find it to be tedious and needlessly finicky to setup. Still better than all the other AAE offerings.
Not ready for prime time
I purchased the Champion II on the 8th of August 2012. On 21 August 2012, it fell apart while attached to my bow. Easy to set up, easy to adjust. Poor quality and lacks durability. Should come with the following label: "use at your own risk!"
Excellent
well made
Works great
Smooth release and increased my accuracy with my old compound bow.
USE WITH PLUNGER
as a target shooter only, who's looking to tighten up my groupings the champion II seems to be a good fit. manufacturer recommends bending wire up slightly to create a "v" shape. i strongly recommend using with a plunger.
On a wooden recurve you will just not have as much adjustment. Using a plunger is like building out your strike plate. It allows you to compensate for arrows that are too weak or too stiff. You would be able to get the same effect if you put a piece of material between the riser and the rest. You would move it away from center and be able to shoot a lighter arrow. The plunger is not necessary, but if you are using a riser that has a plunger bushing it works well with this rest.
I would suspect that your nock point is to low or the spine of the arrow is in correct for the draw weight that you are shooting.
Yes, this will work with a longbow. It attaches with an adhesive back so there is no need to drill holes into your riser. I do not know how this compares to the pin arm arrow support system. I have never seen that kind of elevated rest.
This helps to keep the arrow from sliding off of the rest. Good for hunting, but should not be needed for target shooting. If you roll your fingers when drawing it will also push your arrow off the rest. The draw should be changed if that is happening though.
You can bend the wire if you want . and you wont chew the feathers out. Or you just cant the bow when you draw it . Or just shoot of the shelf if you have that option.
You can, but I would not recommend it. You will get better arrow flight with feathers than you will with vanes. The feathers will lay down as they pass over any surface. A vane will deflect off of any surface it come in contact with.
On a wooden recurve you will just not have as much adjustment. Using a plunger is like building out your strike plate. It allows you to compensate for arrows that are too weak or too stiff. You would be able to get the same effect if you put a piece of material between the riser and the rest. You would move it away from center and be able to shoot a lighter arrow. The plunger is not necessary, but if you are using a riser that has a plunger bushing it works well with this rest.
I would suspect that your nock point is to low or the spine of the arrow is in correct for the draw weight that you are shooting.
Yes, this will work with a longbow. It attaches with an adhesive back so there is no need to drill holes into your riser. I do not know how this compares to the pin arm arrow support system. I have never seen that kind of elevated rest.
Yes, it will work on your bow. The base is made out of what looks like steel.
The rest arm is very durable. This is the best elevated rest that we carry.
It would not need to conform. The rest would be up off of the shelf.
You can tune it by using a plunger button with it. That will be the only way that you could adjust its performance.
a set screw allows the arm to move up or down. the arm can also be turned in and out to accomodate different shaft diameters.
A plunger is not required. Although I would recommend it.