The TopHat® Shaft Shaper allows you to easily and safely adjust your wooden shafts to accept TopHat® Field Points. The Shaft Shaper gently compresses the wood, reducing the diameter to receive field points, without harming the finish on the shaft or distorting the spine. The TopHat® Assembly Tool can be used to hold and rotate the Shaft Shaper. ...read more
Rugged arrow cases from MTM are a traveling archer's favorite. Made of... read more
Finally! A spine tester for the home wood arrow builder that won't... read more
With the built-in guide controls, you can produce precision grinds to both... read more
Replacement (or extra) fletching indexer for the Bitzenburger Dial-O-Fletch fletching jig. Looking... read more
Replacement (or extra) bearing spring for the Bitzenburger Dial-O-Fletch fletching jig. Sold... read more
No needed
The Top Hat threader work the the same with or without this tool. This tool did nothing. Only used it on 11/32 wood shafts.
Can also compress 11/32 shafts to accept 5/16 points
Being a cheapskate I first tried just using the thread cutter & points without buying the shaft shaper. After splitting my second shaft from excessive torque, I ponied up for this tool. It really is necessary for using the TopHat thread cutter & points, and worth the money. I rub a little bar soap on the shaft for lubrication before compressing, threading or installing with the… read more TopHat system. I chuck this tool in my cordless drill, hold the shaft with an arrow-puller, and slowly spin the shaper onto the shaft. I discovered by happy accident that I could compress an 11/32" shaft with the 11/32" tool, and then compress again with the 5/16" tool, and it will accept the 5/15" points and adapters. The only negative to this tool is that after using in a drill, the sizing die can be difficult to unscrew from the tool body. I'm going to start using a little anti-seize on the threads.
Must have for hard wood shafts
This is a must have if you are putting the top hat screw in adaptors on hard wood shafts. I tried it without this tool,let me save you the trouble. Just buy this tool to begin with and save the additional shipping of another order.
Indispensible
I tried putting one adapter on without this tool, just to see if it could be done. It could, but I won't try that again. If you are going to use the top hat adapters, and you really should, you should buy this tool and use it.
Shaft dhaper tool
as instructed
Unfortunately these are sold by the set and we would not be able to sell them individually.
I will pass this along and see if we cannot get a video on youtube.
Howdy, I agree the instructions stink. I figured it out after ruining two shafts. Put the shaping tool in a standard drill, then as you run the drill (on low to medium speed) work the shaft end that you are shaping in and out of the shaping tool a few times. That did the job for me, then you you should be able to use the thread tool without getting it stuck on the shaft. Good luck, after you figure it out it's really easy, but the learning curve is expensive.
I put an 1/8" chamfer on the shaft first with a belt sander. Then I put the shaper in the tool holder. I put the tool holder in a small vise. Then I push & turn the shaft into the shaper. Then I put the thread cutting tool in the tool holder & push and turn the shaft into the thread cutter until it won't go anymore. Then I do the same with the point.
There are several different ways to secure the shafts when using these. You can use an arrow puller or a vise (needs to be padded to not damage arrow)
I put on a latex glove for extra grip. Helped alot.
I find that using one of those little rubber mat jar openers helps, you can also rub paraffin on the tip of the shaft, that helps, or get Magella Gorilla to hold the shaft. Hope this is helpful. Allen Marcel Sent from my iPad
Use an arrow puller type gripper. Works great.
I use a rubber pad like one would use to open a tight top on a jar, or even use as a thin mouse pad. Wrap the pad around the shaft and hold tight to use the shaper tool or to screw on the point with a top hat tool.
Craig, I was able to eventually pull this off - after breaking two of my shafts trying it the way you described; use a power drill, one with the adjustable head grip; place the shaping tool in head of the power drill, as though it is drill bit. I held the drill in one hand the shaft in the other. I used a fairly slow RPM on the drill and then slowly pushed the shaft into the tool as it was spinning. This worked and I was able to shape the rest of my arrows just fine. Using the drill technique is not immediately obvious, and unfortunately the tools come with no instructions. Hope this helps and good luck!
Yes that is correct.